FPVDrone Power Module V1.0 XT60 Plug Current Sensor for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
LongJinSheng #ad - It isnotdesigned to power servos. The on-board switching regulator outputs 5. 3v and a maximum of 3A from up to a 7S LiPo battery. The apm 2. 5 power module is a simple way of providing your APM 2. 5 with clean power from a liPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable.

The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection. Note: the power module is only designed to power APM, a RC receiver and APM accessories GPS, 3DR radio. The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 6S LiPo battery.

FPVDrone Power Module V1.0 XT60 Plug Current Sensor for APM2.8 APM2.6 APM Pixhawk Flight Controller #ad - Use your aircraft's own ESC/BEC for that. Notice: we have many buyer burned this cable when connet it to 6S battery because he solder the cable to our this module cable. Please don't connect or solder any other cable on this current cable, otherwise it will be burned Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable.

Use your aircraft's own ESC/BEC for that. Special for APM2. 5.

More information about LongJinSheng #ad

BW® Glass Fiber Flight Controller Anti-vibration Damping Plate Shock Absorber Set for APM2.5/2.6 /KK /MWC

#ad
BW #ad - Size: 10 x 8 x 1cm / 3. 9 x 3. 1 x 04in. Description: 1. Suit for different various kinds of flight controller, like APM 2. 5/2. 6, kk, mwc 2. Weight: 25g. Size: 10 x 8 x 1cm / 3. 9 x 3. 1 x 04in 4. Weight: 25g package includes: 1 x bw® anti-vibration board 1 x bw® anti-vibration ball 1 x bw® Double-sided adhesive If any questions, please do not hesitate to contact us and we will try our best to help you ! Suit for various kinds of flight controller, like APM 2.

5/2. 6, kk, mwc. Material: Glass fiber. Material: Glass fiber 3.

More information about BW #ad


Similar products



Readytosky 3DR Radio Telemetry Kit 915Mhz 100mW Air + Ground Module Open Source for Standard Version APM2.6 APM2.8 pixhawk 2.4.6 2.4.8 Flight Controller

#ad
Readytosky #ad - Support otg of android cellphones, and computer OTG. It's availabl in 915mhz; and in the following configurations: serial board for the air and USB for the ground. This 3d radio telemetry Kit is small size, light weightunder 4 grams without antenna. If you need download drivers, please check this link : https://www.

Readytosky 3DR Radio Telemetry Kit 915Mhz 100mW Air + Ground Module Open Source for Standard Version APM2.6 APM2.8 pixhawk 2.4.6 2.4.8 Flight Controller #ad - Silabs. Com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers. Weight: 25g. 3dr telemetry kit specifications - very small size - light weight under 4 grams without antenna - 915mhz - receiver sensitivity to -121 dbm - transmit power up to 20dbm 100mw / 250mw - transparent serial link - air data rates up to 250kbps - mavlink protocol framing and status reporting - frequency hopping spread spectrum FHSS - Adaptive time division multiplexing TDM - Support for LBT and AFA - Configurable duty cycle - Built in error correcting code can correct up to 25% data bit errors - Demonstrated range of several kilometers with a small omni antenna - Can be used with a bi-directional amplifier for even more range - Open source firmware - AT commands for radio configuration - RT commands for remote radio configuration - Adaptive flow control when used with APM - Based on HM-TRP radio modules, with Si1000 8051 micro-controller and Si4432 radio module Package including: 1pc X 3DR Radio Telemetry Kit 915mhz 100mW / 250mW Suit for various kinds of flight controller, like APM 2.

5/2. 6, kk, mwc. Material: Glass fiber. Size: 10 x 8 x 1cm / 3. 9 x 3.

More information about Readytosky #ad


Similar products



Readytosky Pixhawk PX4 Flight Controller Autopilot PIX 2.4.8 32 Bit Flight Control Board+Safety Switch+Buzzer+I2C Splitter Expand Module+16GB SD Card

#ad
Readytosky X81 #ad - It's availabl in 915mhz; and in the following configurations: serial board for the air and USB for the ground. This 3d radio telemetry Kit is small size, light weightunder 4 grams without antenna. If you need download drivers, please check this link : https://www. Silabs. Com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers.

2 can 3. Spektrum dsm / dsm2 / dsm-X satellite receiver compatible input 4. Futaba sbus compatible inputs and outputs 5. Ppm signal Input 6. Rssi pwm or voltage Input 7. I2c 8. Spi 9. 3. 3 and 6. 6vadc input 10 The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe; 5.

Readytosky Pixhawk PX4 Flight Controller Autopilot PIX 2.4.8 32 Bit Flight Control Board+Safety Switch+Buzzer+I2C Splitter Expand Module+16GB SD Card #ad - Micro sd recording flight data; Specifications: Microprocessor 1. 32 2 mb flash stm32f427 cortex m4, with hardware floating-point processing unit 2. Weight: 25g. External micro usb interface Packing list: 1 x Pixhawk 2.

More information about Readytosky X81 #ad


Similar products



Readytosky M8N GPS Module Built-in Compass Protective Case with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 Flight Controller

#ad
Readytosky XGT60-BLACK #ad - Weight: 25g. Extra - onboard saw band pass filter - memory rom or flash - Supported antennas Active and passive - Odometer Travelled distance - Data-logger For position, velocity, and time - Operating temp. Antenna is 5. 8g level. The latest 3dr digital design, wiring complete, more secure, beautiful, plus a separate shell, more stable data transmission.

Readytosky M8N GPS Module Built-in Compass Protective Case with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 Flight Controller #ad - The 3dr radio telemetry system is designed as an open source xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. 40° c to 85° c - Storage temp. We have m8n gps for this flight controller, ASIN : B01KK9A8QG. Special designed for pixhawk 2. 4. 6 2. 4. 8 flight controller, aSIN:B07CHQ7SZ4.

Note:if you use it to aPM Flight Controller, Please replace the connect by yourself. The ultimate accuracy is 06 meters, actually almost 09 meters, greater than the previous generation NEO-7N 1. 4-1.

More information about Readytosky XGT60-BLACK #ad


Similar products



FPVKing 6M GPS Module Built-in Compass +Black GPS Folding Antenna Mount Holder for APM2.6 APM2.8 Pixhawk Flight Controller

#ad
FPVKing #ad - Special designed for ardupilot arducopter apm2. 6 2. 8 flight controller. Note:if you use it for pix pixhawk PX4 Flight Controller, Please replace the 6pin connect firstly. Features: - built-in 25*25*4mm high gain ceramic antenna - with l883 compass - built-in eeprom, clear indication of GPS status - With round GPS shell and holder for RC models - Baut rate, make sure no data lost - Built-in reverse polarity protection - Built-in dual color LED, and refresh rate could reset by yoursef - Special designed for Ardupilot Arducopter APM2.

6 2. 8 flight controller if you use it to PIX Pixhawk PX4 flight controller, please replace the 6 pin connector firstly. The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;. Antenna is 5. 8g level. The latest 3dr digital design, plus a separate shell, wiring complete, beautiful, more secure, more stable data transmission.

FPVKing 6M GPS Module Built-in Compass +Black GPS Folding Antenna Mount Holder for APM2.6 APM2.8 Pixhawk Flight Controller #ad - The 3dr radio telemetry system is designed as an open source xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. The 6pin connection was in package gps line: black green: tx yellow: rx red: +5v white: sda orange: scl package included: 1x 6m gPS module built-in compass 1xGPS folding base antenna GPS set fitting seat foldable bracket holderIf any question, welcome to provide! Suit for various kinds of flight controller, very happy to help you!If any suggestion for our products, welcome to contact with us, like APM 2.

More information about FPVKing #ad


Similar products



FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver

#ad
FrSky NPH-01266 #ad - Weight: 25g. With rssi pwm output 0~3. 3v smartport enabled, realizing two-way full duplex transmission. Baut rate, and refresh rate could reset by yourself. For 8 channels in d8 mode you can use the frsky Taranis or XJT, DJT, DFT, DHT and DHT-U modules. Support otg of android cellphones, and computer OTG. Size: 10 x 8 x 1cm / 3.

9 x 3. 1 x 04in. For 8 channels in d8 mode you can use the frsky Taranis or XJT, DFT, DJT, DHT and DHT-U modules. With l883 compass, built in eeprom to make sure no data lost. Or you can use 2 x8r receivers in combination and the channels will sync 1-8 on the first and 9-16 on the second. The x8 protocol is also backward compatible! In D8 mode it work with the DHT, DJT, DFT and DHT-U transmitter modules.

FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver #ad - Parallel two x8R to become a 16 channel receiver. Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control. 32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit. The 6pin connection in package. Features: more number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver.

More information about FrSky NPH-01266 #ad


Similar products



Pixnor Apm2.6 MWC GPS Compass Antenna Folding Fixed Mount Bracket Holder for DJI Red

#ad
Pixnor 172354O63OI5005 #ad - Rod diameter: about 4mm, Height: about 16. 2cm. Cnc aluminum gps folding Antenna Base Mount Holder Bracket Set. Suitable for most DJI WKM Quadcopter Multicopter. Adopt aluminum turning and CNC manufacturing for durable to use. Easy to install and use. Weight: 25g. We have m8n gps for this flight controller, ASIN : B01KK9A8QG.

Special designed for pixhawk 2. 4. 6 2. 4. 8 flight controller, aSIN:B07CHQ7SZ4. Note:if you use it to aPM Flight Controller, Please replace the connect by yourself. The ultimate accuracy is 06 meters, actually almost 09 meters, greater than the previous generation NEO-7N 1. 4-1. 6 meters accuracy. A new generation m8n GPS, with low power consumption and high precision.

Pixnor Apm2.6 MWC GPS Compass Antenna Folding Fixed Mount Bracket Holder for DJI Red #ad - The gps light only can light up when it search the satellite signal outdoor; ROM already been fix, it cannot be flash and change. Attention: the gps can only use in Pixhawk and APM Flight controller, it can't work with other flight controller. Main chip: 6M.

More information about Pixnor 172354O63OI5005 #ad


Similar products



RAYCorp® 1045 10x4.5 Propellers. 8 Pieces4 CW, 4 CCW Black & Red High Quality 10-inch Quadcopter and Multirotors Props + Battery strap

#ad
RAYCorp Manufacturer #ad - The 6pin connection in package. Weight: 25g. Parallel two x8R to become a 16 channel receiver. Smartport enabled, realizing two-way full duplex transmission. More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver. All 16 channels requires the frsky taranis, or the xjt module bound in d16 mode.

RAYCorp® 1045 10x4.5 Propellers. 8 Pieces4 CW, 4 CCW Black & Red High Quality 10-inch Quadcopter and Multirotors Props + Battery strap #ad - The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. With rssi pwm output 0~3. 3v. Antenna is 5. 8g level. The latest 3dr digital design, plus a separate shell, wiring complete, more secure, beautiful, more stable data transmission. The 3dr radio telemetry system is designed as an open source xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios.

100% genuine & brand new. Support otg of android cellphones, and computer OTG. Top-notch manufacturing Standard for Optimal Product Quality. We have m8n gps for this flight controller, ASIN : B01KK9A8QG.

More information about RAYCorp Manufacturer #ad


Similar products



YoungRC F450 Drone Frame Kit 4-Axis Airframe 450mm Quadcopter Frame Kit with Landing Skid Gear

#ad
YoungRC #ad - Size: 10 x 8 x 1cm / 3. 9 x 3. 1 x 04in. The 6pin connection in package. Specification: width: 450mm height: 55mm weight: 280g w/out electronics Motor Mount Bolt Holes: 16/19mm G. Weight: 395g Wheelbase: 17. 7in/450mm net weight: 272g 100% brand new made by advanced engineering material, superstrong &smooth kit recommended usesnot included: a2208/a2212 800kv~1100kv brushless motor ESC 15~25A 1800mAh~3600mAh 3S LiPo battery 1045/8045 Forward&Reverse propeller Package: 1 X F450 Drone Frame Kit 1 set X f450 Landing Gear Skids Suit for various kinds of flight controller, like APM 2.

YoungRC F450 Drone Frame Kit 4-Axis Airframe 450mm Quadcopter Frame Kit with Landing Skid Gear #ad - 5/2. 6, kk, mwc. Material: Glass fiber. Made with high quality ABS Plastic for Maximum Performance, Durability and Balance. Perfect for any multirotor accepting 10 inches pros with rounds HUBS, NOT SQUARED HUBS, NOT KEYED HUBS. Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control.

32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit. Easy assembly. Instructional video:https://www. Youtube.

More information about YoungRC #ad


Similar products



yueton 30Pairs 3.5mm Male Female Banana Plug Bullet Connector Replacements

#ad
yueton CECOMINOD016801 #ad - 100% genuine & brand new. One of the most used propeller for 330 to 450-sized quadocopters, hexacopters and octocopters. Size: 3. 5*12mm d*H. Ultra high strength material:Built from quality glass fiber and polyamide nylon. It is resistant to falling and impact. Integrated pcb connections for direct soldering of your ESCs, make your esc, power supply and other wiring more quickly and safely.

yueton 30Pairs 3.5mm Male Female Banana Plug Bullet Connector Replacements #ad - Pre-threaded brass sleeves for all of the frame bolts. Colored arms for orientation to keep you flying in the right direction. Large mounting tabs on main frame bottom plate for easy camera mounting. Special designed for ardupilot arducopter apm2. 6 2. 8 flight controller. Note:if you use it for pix pixhawk PX4 Flight Controller, Please replace the 6pin connect firstly.

Male female banana plug pack of 30 pairs, 30pcs male plugs and 30pcs female plugs Color: gold Size: 3. 5*12mm d*h material: metal capable of optimizing current flow Suit for various kinds of flight controller, like APM 2. 5/2. 6, kk, mwc. Material: Glass fiber.

More information about yueton CECOMINOD016801 #ad


Similar products