Hypetrain Freestyle 2306 2450KV Motor V1.1-EZO

#ad
T-Motor #ad - And just to be extra sure, the hypetrain freestyle is built around a 2306 stator, but also perform well! As far as performance, every motor gets individually tested before it leaves the factory! This guarantees that each motor will not only look nice, with single strand windings that give it a KV rating of about 2450 RPM per Volt.

Moreover, we wanted it to have a set screw to hold the bell rather than a c-clip, to facilitate motor cleaning and maintenance! specifications kv: 2450 stator diameter: 23 mm stator height: 6 mm weight: 30 grams Wire Length: 100 mm Shaft size: M5 Mounting Screw Pattern: 16x16 mm Input Voltage: 3-5S INCLUDES 1x Hypetrain Freestyle 2306 2450kv Motor 1x M5 Nylock Propeller Nut 4x M3 Mounting Screws The hypetrain freestyle motor is the first official product designed by Rotor Riot! Ride the Hype Train with the Hypetrain!

Inspired by the iconic rotor riot logo, the Hypetrain's three-spoke 7075 aluminum bell showcases the elegant silver coated wire wound over the orange stator. In other words, plenty of power and good efficiency! To ensure reliability, we opted to use high quality silicone wires for the motor leads. We love stylish design - but performance is the priority.

Hypetrain Freestyle 2306 2450KV Motor V1.1-EZO #ad - . The hypetrain freestyle motor is the first official product designed by Rotor Riot! Ride the Hype Train with the Hypetrain! Designed from the ground up with constant input from our best pilots, the attention to detail of the Hypetrain Freestyle motor sets it apart from the competition. That's why we thoroughly considered every aesthetic decision, to ensure that it would not negatively impact the performance of the motor.

The "open bottom" style base allows for considerable weight reduction and improved cooling, and the revolutionary 16x16 mm mounting screw pattern opens up new design possibilities while still maintaining backwards compatibility with legacy frames.

More information about T-Motor #ad

SMA Male to Female Right Angle 90-Degree Adapter Gold Plated Contacts Pack of 2

#ad
onelinkmore OL0444-X #ad - The connector housing and pin in center are made of pure brass to ensure a lower VSWR for higher transmission efficiency. Impedance:50Ω, insertion loss≤015db/3ghz, vswR≤1. 1;teflon insulator ; Color: Gold. Package content : 2 x SMA Female to Male Adapter. Sma male with a pin in center to SMA Female with A hole in center.

Product series:type sma is one kinf of rf coaxial connectors that is widely applied, high reliability and long life, eg: connection for two-way radio, characteristic impedance is 50 Ω, with small-sized thread coupling, This SMA series is small threaded coaxial connectors with high frequency bandwidth, audio, has a wide range of application, video, excellent performance, and other test equipment.

SMA Male to Female Right Angle 90-Degree Adapter Gold Plated Contacts Pack of 2 #ad - Product specification:temp range:-65~+165℃ pe cable-40~+85℃vibration:MIL-STD-202, Method 213Impedance:50ΩFrequency Range:DC~12. 4ghzworking voltage:335v maxinsulation resistance≥ 5000 MΩInsertion loss≤015 db/6ghzsma coaxial adapter body plating:goldplated connector material:brass gender:SMA Plug, male pin/SMA Jack, female pin Style:Right Angle Mounting Type:Free hanging Sma 90 degree angle adapter jack to Plug; Commercial Grade SMA Series Adapters.

More information about onelinkmore OL0444-X #ad


Similar products



FrSky XM Plus Mini Receiver up to 16CH 1.6g Full Range fit for Micro Drone

#ad
FrSky SG_B01N5INCBH_US #ad - Full range, so identical to your X4R and D4R setups. Xm plus receiver supports failsage function for all channels. Ultra mini Only 1. 6g!!! specification: Dimension:21. 5x12x3. 5mmlxwxh Weight: 1. 6g number of channels:up to 16ch from sbusch1~ch15 for pWM, CH16 RSSI for FC Operating Voltage Range:3. 7~10v operating current:[email protected] operating Range:FULL range With RSSI output on board:Analog 0~3.

3v firmware upgradeable compatibility:frsky D16 mode Sma 90 degree angle adapter jack to Plug; Commercial Grade SMA Series Adapters. Sma male with a pin in center to SMA Female with A hole in center. Compatible -- compatible with Frsky X9D Plus X9E X12S transmitter. Weight:1. 6g, especially for fpv racing drone, dimension: 21.

FrSky XM Plus Mini Receiver up to 16CH 1.6g Full Range fit for Micro Drone #ad - 5*12*3. 5mml x w x H. Frsky xm plus mini receiver is perfect for those racers who are looking to lower their AUW, mini drone, such as 130 110 drone. Frsky xm plus is dual antenna frsky xm is only one, with dual antenna, it has strong anti-interference, make sure you can control your drone anytime. Package content : 2 x SMA Female to Male Adapter.

This insanely tiny 2.

More information about FrSky SG_B01N5INCBH_US #ad


Similar products



MG Chemicals 422B Silicone Modified Conformal Coating, 55 ml Bottle

#ad
MG Chemicals 422B-55ML #ad - It protects and insulates electrical and electronic components and assemblies, transformers, relays, including generators, motors, and solenoid coils.8309 liquid or 8310A Gel stripper formulations. Silicone conformal coating 422b is a flexible finish product that provides a protective coating for printed circuit boards against moisture, corrosion, and thermal shock.

This insanely tiny 2. 4ghz diversity receiver available from frsky is the next big thing in miniaturization of racing craft. Perfect for those racers who are looking to lower their AUW. Sma male with a pin in center to SMA Female with A hole in center. Compatible -- compatible with Frsky X9D Plus X9E X12S transmitter.

MG Chemicals 422B Silicone Modified Conformal Coating, 55 ml Bottle #ad - Weight:1. 6g, especially for fpv racing drone, dimension: 21. 5*12*3. 5mml x w x H. Frsky xm plus mini receiver is perfect for those racers who are looking to lower their AUW, mini drone, such as 130 110 drone. Frsky xm plus is dual antenna frsky xm is only one, with dual antenna, it has strong anti-interference, make sure you can control your drone anytime.

Certified ul 94 v-0 file# E203094. We recommend curing in a convection oven at 65 degree C for one hour, but other temperature and time combinations can work well.

More information about MG Chemicals 422B-55ML #ad


Similar products



FrSky R-XSR Ultra SBUS/CPPM D16 16CH Mini Redundancy Receiver 1.5g for RC Multirotor FPV Racing Drone

#ad
FrSky #ad - Up to 16ch from sbus ch1-ch15 for pwm, such as f3, ch16 rssi for fc, naze32 flight controller . Fluoresces under UV-A light blacklight. The r-xsr is a standalone receiver with all the functions of XSR, in addition, it's almost 1/3 size and 1/3 weight of XSR receiver. Maximum constant service temperature of 200 °C 392 °F.

. Full range, so identical to your X4R and D4R setups. Xm plus receiver supports failsage function for all channels. Moreover, there redundancy function is integrated into this tiny receiver ensures the security, and the IPEX connector makes it more convenient for you to replace antennas. Ultra mini size and light weight.

FrSky R-XSR Ultra SBUS/CPPM D16 16CH Mini Redundancy Receiver 1.5g for RC Multirotor FPV Racing Drone #ad - Providing outstanding customer service is our number one priority. The connector housing and pin in center are made of pure brass to ensure a lower VSWR for higher transmission efficiency. This insanely tiny 2. 4ghz diversity receiver available from frsky is the next big thing in miniaturization of racing craft.

Perfect for those racers who are looking to lower their AUW. Easy rework and repairs: solder through the coating or remove with MG Cat. Ipex connector, replaceable antennas.

More information about FrSky #ad


Similar products



Pack of 3 Tempered Glass Screen Protector for Gopro Hero 4 Session Hero 5 Session, Akwox 0.3mm 9H Hard Scratch-Resistant Camera Lens Film for GoPro Hero4 Session/Hero5 Session Camera Accessories

#ad
Akwox AK-GL025 #ad - Validated for selective robotic coating equipment including PVA and Nordson ASYMTEK. Supports redundancy function Support telemetry and Smart Port enabled. Providing outstanding customer service is our number one priority. High hardness: 9h surface hardness tempered glass screen protector for GoPro session.

Why akwox: akwox company is always committing to provide people inspired products. Our designers adhere to provide consumers' with stylish and practical products, at the same time with top quality. We are aimed to : meet consumer demand and provide satisfied service! Perfect protection The Lens Protector for GoPro Hero4 Session/Hero5 Session make of Highest quality Tempered-Glass, offer best protection for your camera lens from shattering, with an industry leading hardness of 9H.

Pack of 3 Tempered Glass Screen Protector for Gopro Hero 4 Session Hero 5 Session, Akwox 0.3mm 9H Hard Scratch-Resistant Camera Lens Film for GoPro Hero4 Session/Hero5 Session Camera Accessories #ad - The connector housing and pin in center are made of pure brass to ensure a lower VSWR for higher transmission efficiency. Maximum constant service temperature of 200 °C 392 °F. Compatible -- compatible with Frsky X9D Plus X9E X12S transmitter. Weight:1. 6g, especially for fpv racing drone, dimension: 21. 5*12*3.

5mml x w x H.

More information about Akwox AK-GL025 #ad


Similar products



M3 Flight Controller Anti-Vibration Fixed Screws Mounting Hardware Standoffs with M3 Rubber Washer Rings for Naze32 CC3D F3 F4 Flight Controller12Sets

#ad
LongJinSheng #ad - Maximum constant service temperature of 200 °C 392 °F. The connector housing and pin in center are made of pure brass to ensure a lower VSWR for higher transmission efficiency. Package content : 2 x SMA Female to Male Adapter. Featuring maximum protection from high impact drops, scratches, scrapes, and bumps.

High transmittance Transparent: With not influence the Video shooting effect. Super toughness: the protector will not break into small sharp pieces even if it is broken, which makes it safer than other glass products. Easily installation: wipe down your lens, carefully align the space to setup the lens protector to your Gopro Camera Lens.

M3 Flight Controller Anti-Vibration Fixed Screws Mounting Hardware Standoffs with M3 Rubber Washer Rings for Naze32 CC3D F3 F4 Flight Controller12Sets #ad - Package included: 3 x lens glass protector for Gopro Session, 3 x wet and dry Screen Cleaning Wipes, 3 x Sticker Camera is not included. Anti-vibration screws are the best way to soft mount your flight controller. Flight controller anti-vibration screws are easy to install, perfect fit, and significant vibration elimination.

Compatible with: naze32 cc3d f3 f4 flight controller and PCB Power Distribution Board PDB. Material: rubber and Ultra Hard and Durable Alloy Steel and brass. Recommended to use with our m3 nylon screws, ASIN:B07214815H. Validated for selective robotic coating equipment including PVA and Nordson ASYMTEK.

More information about LongJinSheng #ad


Similar products



FPV Antenna Adapter SMA Male to Female 45 Degree Antenna Adapter Gold Plated Connector for FPV Race RX5808 Fatshark Goggles Pack of 2

#ad
onelinkmore OL-3310 #ad - For fpv race rx5808 fatshark goggles antenna, Signal Booster, Repeaters, Radio, Extension Cable, fpv drone, rf coaxial Coax, FPV Quadcopter Multicopter. Sma male with a pin in center to SMA Female with A hole in center. Teflon insulator ; color: Gold;Material: CopperNot Alloy, Low-loss. Validated for selective robotic coating equipment including PVA and Nordson ASYMTEK.

Us-based customer service & technical support - should you ever run into any problems or need assistance, we are here to help! We offer 24/7 e-mail support and are available for phone calls Monday-Friday between the hours of 9 am - 4 pm PST. Featuring maximum protection from high impact drops, scrapes, scratches, and bumps.

High transmittance Transparent: With not influence the Video shooting effect. Super toughness: the protector will not break into small sharp pieces even if it is broken, which makes it safer than other glass products. Easily installation: wipe down your lens, carefully align the space to setup the lens protector to your Gopro Camera Lens.

FPV Antenna Adapter SMA Male to Female 45 Degree Antenna Adapter Gold Plated Connector for FPV Race RX5808 Fatshark Goggles Pack of 2 #ad - Package included: 3 x lens glass protector for Gopro Session, 3 x wet and dry Screen Cleaning Wipes, 3 x Sticker Camera is not included. Anti-vibration screws are the best way to soft mount your flight controller. Flight controller anti-vibration screws are easy to install, perfect fit, and significant vibration elimination.

Compatible with: naze32 cc3d f3 f4 flight controller and PCB Power Distribution Board PDB.

More information about onelinkmore OL-3310 #ad


Similar products



iFlight 150mm 2.4G Receiver Antenna Generation 4 RF113 smaller IPEX Port for Latest FrSky X4R-SB Receiver and Remote Controller pack of 20pcs

#ad
iFlight #ad - Featuring maximum protection from high impact drops, scratches, scrapes, and bumps. High transmittance Transparent: With not influence the Video shooting effect. Super toughness: the protector will not break into small sharp pieces even if it is broken, which makes it safer than other glass products. Easily installation: wipe down your lens, carefully align the space to setup the lens protector to your Gopro Camera Lens.

Package included: 3 x lens glass protector for Gopro Session, 3 x wet and dry Screen Cleaning Wipes, 3 x Sticker Camera is not included. Anti-vibration screws are the best way to soft mount your flight controller. Flight controller anti-vibration screws are easy to install, perfect fit, and significant vibration elimination.

iFlight 150mm 2.4G Receiver Antenna Generation 4 RF113 smaller IPEX Port for Latest FrSky X4R-SB Receiver and Remote Controller pack of 20pcs #ad - Compatible with: naze32 cc3d f3 f4 flight controller and PCB Power Distribution Board PDB. Material: rubber and Ultra Hard and Durable Alloy Steel and brass. Recommended to use with our m3 nylon screws, ASIN:B07214815H. Sma 45 degree angle adapter jack to Plug; Commercial Grade SMA Series Adapters. Teflon insulator ; color: Gold;Material: CopperNot Alloy, Low-loss.

Ultra mini size and light weight. Sma male with a pin in center to SMA Female with A hole in center.

More information about iFlight #ad


Similar products



DALPROP 16pcs Cyclone T5046C 5046 3 Blades 5.0 x 4.6 CW CCW Propeller for FPV Racing Quadcopter Frame Kit 4sets, mix color

#ad
DALPROP Cyclone T5046C #ad - Up to 16ch from sbus ch1-ch15 for pwm, ch16 rssi for fc, such as f3, naze32 flight controller . Protect your perfectly henever the control signal is lost for a period of time. This insanely tiny 2. 4ghz diversity receiver available from frsky is the next big thing in miniaturization of racing craft. Perfect for those racers who are looking to lower their AUW.

Teflon insulator ; color: Gold;Material: CopperNot Alloy, Low-loss. Providing outstanding customer service is our number one priority. High hardness: 9h surface hardness tempered glass screen protector for GoPro session. Switchable sbuS/ CPPM signal output. 2. 4g receiver antenna with IPEX 4 Generation connector.

DALPROP 16pcs Cyclone T5046C 5046 3 Blades 5.0 x 4.6 CW CCW Propeller for FPV Racing Quadcopter Frame Kit 4sets, mix color #ad - More unbreakable and anti-crash: t5046C Tri-Blade propellers adopted high toughness German Bayer PC material, resistance to crash, long service life. For fpv race rx5808 fatshark goggles antenna, fpv drone, Signal Booster, rf coaxial Coax, Repeaters, Extension Cable, Radio, FPV Quadcopter Multicopter. Sma male with a pin in center to SMA Female with A hole in center.

Sma male with a pin in center to SMA Female with A hole in center. Fluoresces under UV-A light blacklight.

More information about DALPROP Cyclone T5046C #ad


Similar products



Neewer - Set of 4 Hexagonal Screwdrivers Made of Titanium Nitride with Coloured Handles.Compatible with 1.5, 2, 2.5 and 3mm Screws.

#ad
Neewer 99061486 #ad - 5. 9 inch 150mm - length, rF113 Silver plated Wire Material. Featuring maximum protection from high impact drops, scratches, scrapes, and bumps. High transmittance Transparent: With not influence the Video shooting effect. Super toughness: the protector will not break into small sharp pieces even if it is broken, which makes it safer than other glass products.

Easily installation: wipe down your lens, carefully align the space to setup the lens protector to your Gopro Camera Lens. Package included: 3 x lens glass protector for Gopro Session, 3 x wet and dry Screen Cleaning Wipes, 3 x Sticker Camera is not included. Anti-vibration screws are the best way to soft mount your flight controller.

Neewer - Set of 4 Hexagonal Screwdrivers Made of Titanium Nitride with Coloured Handles.Compatible with 1.5, 2, 2.5 and 3mm Screws. #ad - Flight controller anti-vibration screws are easy to install, perfect fit, and significant vibration elimination. Compatible with: naze32 cc3d f3 f4 flight controller and PCB Power Distribution Board PDB. Material: rubber and Ultra Hard and Durable Alloy Steel and brass. Recommended to use with our m3 nylon screws, ASIN:B07214815H.

Sma 45 degree angle adapter jack to Plug; Commercial Grade SMA Series Adapters. Precision machining, High sensitivity, Low loss signal stability, High quality. A must have for frsky XM+ and X4R rx/tx field repair.

More information about Neewer 99061486 #ad


Similar products