OpenPilot CC3D Evo Flight Controller 32-bit Case Side Pin 90 Degree +Cables

#ad
USAQ #ad - Software support for windows, mac and Linux Direct high speed USB support with no drivers required, a truly plug and play device. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot software. The cc3d board is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware.

Features: multirotor controller with auto-level, including tricopters, quadcopters and hexacopters flybarless helicopter controller with auto-level Fixed Wing UAV controller Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.

OpenPilot CC3D Evo Flight Controller 32-bit Case Side Pin 90 Degree +Cables #ad - The new included Flexiport provides either I2C connectivity or a second serial port. The board shares a lot with the Revolution platform, including the powerful OpenPilot architecture and the cross-platform Ground Control Station GCS. Spektrum satellite receiver support futaba s-bus hardware support and PPM Innovative Flexi-port technology for superior port flexibility 4Mbits on-board EEPROM for configuration storage Specs: Size: 36x36mm Weight: 5.

7g mounting: M3 holes @ 305mm square included: cc3d flight controller Rev C NOTE: Color may vary, some PCBs will be delivered in a black finish. The coptercontrol platform has been designed from the ground up to perform a host of functions from auto-level, multi-copter, Fixed wing UAV's and even Flybarless Helicopter support.

More information about USAQ #ad

RAYCorp® 1045 10x4.5 Propellers. 8 Pieces4 CW, 4 CCW Black & Red High Quality 10-inch Quadcopter and Multirotors Props + Battery strap

#ad
RAYCorp Manufacturer #ad - RAYCorp® 1045 10x4.5 Propellers. 8 Pieces4 CW, 4 CCW Black & Red High Quality 10-inch Quadcopter and Multirotors Props + Battery strap #ad - Main characteristics Diameter: 10inches Pitch: 4. 5 shaft diameter : 6 mm weight: 10 grams material : high quality abs plastic Pack of 8 propellers, 4 clockwise cw & 4 counter-Clockwise CCW - Color : Black 4 props & Red 4 props. Made with high quality ABS Plastic for Maximum Performance, Durability and Balance.

Perfect for any multirotor accepting 10 inches pros with rounds HUBS, NOT SQUARED HUBS, NOT KEYED HUBS. Top-notch manufacturing Standard for Optimal Product Quality. 100% genuine & brand new. One of the most used propeller for 330 to 450-sized quadocopters, hexacopters and octocopters.

More information about RAYCorp Manufacturer #ad


Similar products



PDB XT60 Matek Power Distribution Board Matek Systems, BEC 5V and 12V, Copper and 4-Layers PCB, and 4pcs Sponge Mat Landing Pad

#ad
H-shopping #ad - Dc/dc synchronous buck regulator, Efficiency is up to 95%. 4 * 20a esc output 25a max, 25a peak current 10 seconds/minute per output. Providing synchronized & regulated dc 5v outputs & linear regulated dc 12v for powering camera, Video Transmitter, servos, BEC 5V 12V Output 】- 20A continuous current per output, RC Receiver, Flight Controller, LED, etc.

4pcs sponge mat landing pad gear is suitable for most drone 】 -- great for mini quads from 180mm to 300mm in size, great replacement pads for quadcopters like QAV210 QAV250 QAV-R 180 220 260 Martain II and so on. Super light, strengthen shockproof, anti-static. Voltage: 5. 0 +/- 01vdc - continuous current: 3 amps - short-circuit tolerant 10 seconds/minute - LED indicates voltage is in regulation BEC 12V output: - The battery should be 4SLiPo - Standard output designed to power cameras and video transmitters, etc.

PDB XT60 Matek Power Distribution Board Matek Systems, BEC 5V and 12V, Copper and 4-Layers PCB, and 4pcs Sponge Mat Landing Pad #ad - Top-notch manufacturing Standard for Optimal Product Quality. Made with high quality ABS Plastic for Maximum Performance, Durability and Balance. Perfect for any multirotor accepting 10 inches pros with rounds HUBS, NOT SQUARED HUBS, NOT KEYED HUBS. Support 3s-4s battery 9-18v 】-- batteris may range from 3s -4s 3s 4s lipo Battery, while we do not recommend that, some customer said 2S is also available, some of device may not work because of power.

Suitable for standard cc3d f3 naze32 f4 f7 flight controller 】- suitable for m3 standoff or screw. The size is 36*36mm, can be used for the standard cc3d F3 F4 F7 Naze32 Fligh Controller Standard size is also 36*36mm, mounting holes 30

More information about H-shopping #ad


Similar products



HobbyKing Matek PDB-XT60 w/BEC 5V and 12V

#ad
HobbyKing #ad - It also provides linear regulated dc 12v for powering Cameras, Servos, LEDs, Video Transmitters, Flight Controllers, RC receiver, etc. A great package to get your Racing Drones powered up and racing. Features:• 2oz copper, 4-layers and 1. 6mm pcb• built-in xt60 socket• total 6 pairs esc solder tabs are fit for h or x type frame• 5v and 12v output led indicators• regulated 5v and 12v outputs• Short circuit tolerantSpecs:Input voltage range: 9 - 18V DC 3S-4S LiPoly operationOutput continuous current: 25Ax4 or 15Ax6Output Peak current 10 seconds/minute: 30Ax4 or 20Ax6BEC 5V output: 5V/2A Max.

2. 5a 10s/minuteoutput ripple: 40mv vin= 16v, vout= [email protected] loadshort-circuit tolerant: 5 seconds/minuteBEC 12V output 4S LiPoly, 13~18V DC: 12V/500mA Max. 08a 5s/minutebec 12v output 3s lipoly: =3s lipoly voltage - 1VDimensions: 36 x 50 x 4 mm without XT60Mounting: 305 x 305mm, Φ3mmWeight: 7. 5g w/o xt60, 11g w/ xt60 pack of 8 propellers, 4 clockwise cw & 4 counter-Clockwise CCW - Color : Black 4 props & Red 4 props.

HobbyKing Matek PDB-XT60 w/BEC 5V and 12V #ad - 4 * 20a esc output 25a max, 25a peak current 10 seconds/minute per output. Providing synchronized & regulated dc 5v outputs & linear regulated dc 12v for powering camera, Video Transmitter, servos, BEC 5V 12V Output 】- 20A continuous current per output, RC Receiver, Flight Controller, LED, etc.4pcs sponge mat landing pad gear is suitable for most drone 】 -- great for mini quads from 180mm to 300mm in size, great replacement pads for quadcopters like QAV210 QAV250 QAV-R 180 220 260 Martain II and so on.

More information about HobbyKing #ad


Similar products



FlySky 2.4GHz 6 Channel Digital Transmitter and Receiver Radio System

#ad
Venom Group International FS-T6 #ad - Atomik rc is proud to introduce the FlySky FS-T6 2. 4ghz 6 channel digital Transmitter and Receiver Radio System. 3. 1 inch backlit LCD Display. Rf range: 2. 40-2. 48ghz. Power: 12v dc 8 aa - Not Included. 2. 4ghz Technology. Weight: 875. 4 g 309oz. Charger Port. Model type: Helicopter/Airplane. Complete system Includes Transmitter and Receiver.

Support 3s-4s battery 9-18v 】-- batteris may range from 3s -4s 3s 4s lipo Battery, while we do not recommend that, some customer said 2S is also available, some of device may not work because of power. Suitable for standard cc3d f3 naze32 f4 f7 flight controller 】- suitable for m3 standoff or screw.

FlySky 2.4GHz 6 Channel Digital Transmitter and Receiver Radio System #ad - The size is 36*36mm, can be used for the standard cc3d F3 F4 F7 Naze32 Fligh Controller Standard size is also 36*36mm, mounting holes 305mm square spacing suitable, mounting holes 305mm spuare spacing. Used for most fpv racing drone 】-- with 305*305mm hole to hole size, the pdb can are a standard size for 180 sized quads drone & up, such as 190 200 210 220 230 250 Racing Drone.

More information about Venom Group International FS-T6 #ad


Similar products



YoungRC F450 Drone Frame Kit 4-Axis Airframe 450mm Quadcopter Frame Kit with Landing Skid Gear

#ad
YoungRC #ad - Support 3s-4s battery 9-18v 】-- batteris may range from 3s -4s 3s 4s lipo Battery, some customer said 2S is also available, while we do not recommend that, some of device may not work because of power. Suitable for standard cc3d f3 naze32 f4 f7 flight controller 】- suitable for m3 standoff or screw.

The size is 36*36mm, can be used for the standard cc3d F3 F4 F7 Naze32 Fligh Controller Standard size is also 36*36mm, mounting holes 305mm square spacing suitable, mounting holes 305mm spuare spacing. Used for most fpv racing drone 】-- with 305*305mm hole to hole size, the pdb can are a standard size for 180 sized quads drone & up, such as 190 200 210 220 230 250 Racing Drone.

YoungRC F450 Drone Frame Kit 4-Axis Airframe 450mm Quadcopter Frame Kit with Landing Skid Gear #ad - Integrated pcb connections for direct soldering of your ESCs Pre-threaded brass sleeves for all of the frame bolts. Ultra high strength material:Built from quality glass fiber and polyamide nylon. It is resistant to falling and impact. Integrated pcb connections for direct soldering of your ESCs, make your esc, power supply and other wiring more quickly and safely.

Pre-threaded brass sleeves for all of the frame bolts. Colored arms for orientation to keep you flying in the right direction. Large mounting tabs on main frame bottom plate for easy camera mounting.

More information about YoungRC #ad


Similar products



Readytosky 2212 920KV Brushless Motors CW CCW for F330 X525 F450 F500 F550 DJI Phantom Quadcopter4PCS

#ad
Readytosky #ad - Complete system Includes Transmitter and Receiver. Ergonomic Design. 3. 1 inch backlit LCD Display. Specification: 2212 920kv Brushless Motor Outer diameter: 28. 0 mm height: 24. 0 mm without shaft kv: 920kv fit for dji phantom f330 x525 450 500 550quadcopter multirotor Rotation direction: Left hand tread Not Original DJI Phantom Product Feather: Good quality - With rigorous testing, you can take it easy to use.

. Support 3s-4s battery 9-18v 】-- batteris may range from 3s -4s 3s 4s lipo Battery, while we do not recommend that, some customer said 2S is also available, some of device may not work because of power. Suitable for standard cc3d f3 naze32 f4 f7 flight controller 】- suitable for m3 standoff or screw.

Readytosky 2212 920KV Brushless Motors CW CCW for F330 X525 F450 F500 F550 DJI Phantom Quadcopter4PCS #ad - The size is 36*36mm, can be used for the standard cc3d F3 F4 F7 Naze32 Fligh Controller Standard size is also 36*36mm, mounting holes 305mm square spacing suitable, mounting holes 305mm spuare spacing. Used for most fpv racing drone 】-- with 305*305mm hole to hole size, the pdb can are a standard size for 180 sized quads drone & up, such as 190 200 210 220 230 250 Racing Drone.

100% genuine & brand new.

More information about Readytosky #ad


Similar products



HOBBYMATE M3 Nylon Standoffs 4mm for FPV Drone Quadcopter Building PC PCB Motherboard Standoffs

#ad
HOMEMART #ad - Come with the plastic box: spacers male-female 6mm + 6mm, m3 10pcs spacers male-female 10mm + 6mm, m3 10pcs spacers male-female 12mm + 6mm, m3 10pcs screws m3 x 6mm 60pcs nuts m3 60pcs package include: 1 Nylon Hex Screw Nut Assortment Kit in box Pack of 8 propellers, M3 10pcs Spacers Male-Female 20mm + 6mm, M3 10pcs Spacers Male-Female 15mm + 6mm, M3 10pcs Spacers Male-Female 8mm + 6mm, 4 clockwise cw & 4 counter-Clockwise CCW - Color : Black 4 props & Red 4 props.

Total 180 pieces. Complete system Includes Transmitter and Receiver. Made with high quality ABS Plastic for Maximum Performance, Durability and Balance. Perfect for any multirotor accepting 10 inches pros with rounds HUBS, NOT SQUARED HUBS, NOT KEYED HUBS. Easy assembly. Instructional video:https://www. Youtube.

HOBBYMATE M3 Nylon Standoffs 4mm for FPV Drone Quadcopter Building PC PCB Motherboard Standoffs #ad - Com/watch?v=zgKRQ-jxSUE. 3. 1 inch backlit LCD Display. Ultra high strength material:Built from quality glass fiber and polyamide nylon. It is resistant to falling and impact. Integrated pcb connections for direct soldering of your ESCs, make your esc, power supply and other wiring more quickly and safely.

More information about HOMEMART #ad


Similar products



Hobbypower SimonK 30A ESC Brushless Speed Controller BEC 2A for Quadcopter F450 X525 Pack of 4 pcs

#ad
Hobbypower #ad - 16khz motor frequency, giving fastest response of the motor, and quietest operation as well no 8KHz squeal. Complete system Includes Transmitter and Receiver. Highest accuracy with crystal Oscillator Temperature won't affect the PWM operating range like other cheap ESC's. 100% genuine & brand new. Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate.

Esc specs: Cont. 5v & 12v output led indicators & Short circuit tolerant. For sale is 4pcs 30A SimonK firmware Brushless ESC. Made with high quality ABS Plastic for Maximum Performance, Durability and Balance. Perfect for any multirotor accepting 10 inches pros with rounds HUBS, NOT SQUARED HUBS, NOT KEYED HUBS.

Hobbypower SimonK 30A ESC Brushless Speed Controller BEC 2A for Quadcopter F450 X525 Pack of 4 pcs #ad - Ergonomic Design. No low voltage cutoff, because any cutoff in a multirotor = crash. Ultra high strength material:Built from quality glass fiber and polyamide nylon. It is resistant to falling and impact. Integrated pcb connections for direct soldering of your ESCs, make your esc, power supply and other wiring more quickly and safely.

Pre-threaded brass sleeves for all of the frame bolts. Colored arms for orientation to keep you flying in the right direction.

More information about Hobbypower #ad


Similar products



HOBBYMATE XT60 PDB Power Distribution Board - Support 3-6S Input, 5V/12V Output Support The LC Filter, w/Current Sensor

#ad
HOMEMART #ad - One of the most used propeller for 330 to 450-sized quadocopters, hexacopters and octocopters. Ultra high strength material:Built from quality glass fiber and polyamide nylon. It is resistant to falling and impact. Integrated pcb connections for direct soldering of your ESCs, make your esc, power supply and other wiring more quickly and safely.

Pre-threaded brass sleeves for all of the frame bolts. Colored arms for orientation to keep you flying in the right direction. Large mounting tabs on main frame bottom plate for easy camera mounting. 2. 4ghz Technology. 3. 1 inch backlit LCD Display. Ergonomic Design. 100% genuine & brand new. Easy assembly. Instructional video:https://www.

HOBBYMATE XT60 PDB Power Distribution Board - Support 3-6S Input, 5V/12V Output Support The LC Filter, w/Current Sensor #ad - Youtube. Com/watch?v=zgKRQ-jxSUE. Hobbymate xt60-pdb was integrated bec 5v 3a the 12v 05a the output power for quadcopter camera, VTX, Receiver, Led Board and osd.

More information about HOMEMART #ad


Similar products



AKK KC04 5.8G 600mW FPV Transmitter 700TVL 2.8mm 120 Degree FPV Camera for Racing Quadcopter

#ad
AKK #ad - Soldered with 3pcs 3. 5mm gold female plug, very convenient to connect motor. Highest accuracy with crystal Oscillator Temperature won't affect the PWM operating range like other cheap ESC's. Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate. 16khz motor frequency, giving fastest response of the motor, and quietest operation as well no 8KHz squeal.

Hobbymate fpv drone pdb make the connection easy between the flight controller and PDB board and to the esc, what's more is if you don't have a socket for esc's, you can also solder the esc on the PDB board easy and make the building clean and clear. Top-notch manufacturing Standard for Optimal Product Quality.

AKK KC04 5.8G 600mW FPV Transmitter 700TVL 2.8mm 120 Degree FPV Camera for Racing Quadcopter #ad - Small size and light weight, Signal System: NTSC. Support 3s-4s battery 9-18v 】-- batteris may range from 3s -4s 3s 4s lipo Battery, while we do not recommend that, some customer said 2S is also available, some of device may not work because of power. Suitable for standard cc3d f3 naze32 f4 f7 flight controller 】- suitable for m3 standoff or screw.

The size is 36*36mm, can be used for the standard cc3d F3 F4 F7 Naze32 Fligh Controller Standard size is also 36*36mm, mounting holes 305mm square spacing suitable, mounting holes 305mm spuare spacing. Used for most fpv racing drone 】-- with 30

More information about AKK #ad


Similar products