RPM 73862 Nerf Bars for The Traxxas LCG Slash 2WD, Black

#ad
HRPAA RPM73862 #ad - Designed to increase durability. The chassis layout of the low center of gravity chassis LCG Slash 2WD is different than the original high center of gravity chassis hcg, requiring a different Nerf bar design. Made by rpm r/c products, a United States based company where resources are sourced from American producers.

. Stock replacement for traxxas #5833, #5833A and #5833G nerf bars. Replaces weaker stock components, check for full parts compatibility. The additional cross bracing optimizes rigidity while absorbing additional impact energy anything less than RPM would have Crumpled under! RPM Nerf bars are proudly made in the USA, molded in either blue or black from our engineering grade nylons and backed with our limited Lifetime warranty against breakage.

RPM 73862 Nerf Bars for The Traxxas LCG Slash 2WD, Black #ad - Tech notes: rpm nerf bars are stock replacement parts, sold in pairs and work with all stock Traxxas chassis running Traxxas #5833, #5833A and #5833G Nerf bars. Our slash 2wd lcg nerf bars fix that problem and are a direct, perfect fit! RPM Nerf bars have added structural support to help strengthen the body and reduce impact forces transferred to the chassis.

More information about HRPAA RPM73862 #ad

Traxxas 5831 Low CG Lower Chassis Model Car Parts, Black

#ad
Traxxas 5831 #ad - Lower chassis, low cg black this item is a genuine Traxxas spare part/accessory that is supplied in original retail packaging. Exploded views of your model can be found on the Traxxas website. Use original traxxas parts to get the most out of you Traxxas RTR vehicles. Please refer to your vehicle's user for selecting the correct part.

More information about Traxxas 5831 #ad


Similar products



RPM 80592 Rear A-Arms Black Slash Black

#ad
HRP Distribution RPM80592 #ad - Exploded views of your model can be found on the Traxxas website. Please refer to your vehicle's user for selecting the correct part. Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA! Backed by rPM's world-renowned breakage warranty. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm.

Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Use original traxxas parts to get the most out of you Traxxas RTR vehicles. For the Slash 2WD. The upper axle carrier hole. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used.

More information about HRP Distribution RPM80592 #ad


Similar products



RPM Front Shock Tower 2WD Electric Slash, Stampede, Rustler, Bandit, Black

#ad
HRP Distribution RPM80852 #ad - For the Slash 2WD. Exploded views of your model can be found on the Traxxas website. Designed to increase durability. Replaces weaker stock components. Rpm shock towers are molded in black and are made from our well-reputed blend of materials. Please refer to your vehicle's user for selecting the correct part. These shock towers are so strong; we back them with our extremely well known policy against breakage.

Use original traxxas parts to get the most out of you Traxxas RTR vehicles. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

RPM Front Shock Tower 2WD Electric Slash, Stampede, Rustler, Bandit, Black #ad - Proudly made in the USA. Our design uses an i-beam structure that adds tremendous levels of strength and rigidity that is far superior to u-shaped or flat designs. Backed by rPM's world-renowned breakage warranty. Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used.

Rpm shock towers for traxxas 1/10th scale trucks are designed to add strength and support to the front-end suspension components of these great vehicles. The upper axle carrier hole.

More information about HRP Distribution RPM80852 #ad


Similar products



RPM Rear Shock Tower Slash, Rustler, Stampede, Bandit, Black

#ad
HRP Distribution RPM80832 #ad - Once again, we've exceeded our own expectations with this shock tower. Our version of this shock tower uses an I-Beam construction that improves durability and rigidity as well. Proudly made in the USA. Replaces weaker stock components. Exploded views of your model can be found on the Traxxas website. The upper axle carrier hole.

Rpm rear shock towers for the electric versions of the Stampede, Rustler & Bandit as well as the Slash were designed with one thing in mind – rugged durability. Replaces weaker stock components. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

Designed to increase durability. Rpm rear shock towers for the traxxas Slash, Electric Stampede, Electric Rustler & Bandit are molded in black and are backed by our famous breakage warranty. Proudly made in the USA. At the base of the shock tower, we've improved the screws' head clearance of the bulkhead mounting screws to eliminate the bind normally associated with the stock rear shock tower.

RPM Rear Shock Tower Slash, Rustler, Stampede, Bandit, Black #ad - While we've maintained all stock geometry on these shock towers, we've beefed them up in all the right places to eliminate annoying rear shock tower breakage. All these design elements combine to create the ultimate lightweight, bulletproof rear shock tower for the electric versions of the Rustler & Stampede.

More information about HRP Distribution RPM80832 #ad


Similar products



81002 Rear Bumper Black Slash Pack of 38 - RPM RPM

#ad
HRP (Level 3 Products) RPM81002 #ad - Please refer to your vehicle's user for selecting the correct part. Proudly made in the USA. Use original traxxas parts to get the most out of you Traxxas RTR vehicles. Designed to increase durability. Backed by rPM's world-renowned breakage warranty. For the Slash 2WD. Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA!

For the Slash 2WD. Exploded views of your model can be found on the Traxxas website. Tech notes: rpm highly recommends the use of an RPM rear bumper mount #80902 or #80905 for full rear-end crash and bash-proof protection. The upper axle carrier hole. Backed by rPM's world-renowned breakage warranty. To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm.

81002 Rear Bumper Black Slash Pack of 38 - RPM RPM #ad - Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Proudly made in the USA. Replaces weaker stock components. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. These rear shock towers can be used on the Traxxas Bandit as well, However, there are no provisions for a rear wing built in.

More information about HRP (Level 3 Products) RPM81002 #ad


Similar products



Traxxas 5830 Low-CG Conversion Kit for 1/10 Scale Slash 2WD, Blue

#ad
Traxxas TRA5830 #ad - Rpm is a proud american manufacturer designing and manufacturing 100% of our molded products right here in the United States. For the Slash 2WD. Please refer to your vehicle's user for selecting the correct part. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

Exploded views of your model can be found on the Traxxas website. The low-cg conversion kit lowers the chassis, battery and electronic components to bring all the advantages of a low center of gravity to the 2WD short-course trucks including the Slash, Raptor and Robby Gordon Edition Dakar Slash. Proudly made in the USA.

Traxxas 5830 Low-CG Conversion Kit for 1/10 Scale Slash 2WD, Blue #ad - Complete low center-of-Gravity chassis conversion kit for 2WD Slash models. The upper axle carrier hole. Lowers chassis one inch 33mm/1. 3in; over 45% lower battery position. Replaces weaker stock components. Traxxas now offers a complete Low Center-of-Gravity chassis conversion kit for 2WD Slash models. Backed by rPM's world-renowned breakage warranty.

Proudly made in the USA. Includes chassis, lower chassis, battery hold-down; front and rear battery retainers, nerf bars 2, and front shock springs.

More information about Traxxas TRA5830 #ad


Similar products



RPM 80952 Front Bumper/Skid Black Slash Black

#ad
HRP Distribution RPM80952 #ad - Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. Complete low center-of-Gravity chassis conversion kit for 2WD Slash models. Tech notes: weight comparison is based on the weight of the stock Traxxas bumper along with the weight of the support ring and hardware all of which is permanently removed once the RPM bumper skid plate is installed.

Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Lowers chassis one inch 33mm/1. 3in. Tech notes: rpm highly recommends the use of an RPM rear bumper mount #80902 or #80905 for full rear-end crash and bash-proof protection. Over 45% lower battery position.

RPM 80952 Front Bumper/Skid Black Slash Black #ad - Designed to increase durability. Backed by rPM's world-renowned breakage warranty. These rear shock towers can be used on the Traxxas Bandit as well, However, there are no provisions for a rear wing built in. For the Slash 2WD. Replaces weaker stock components. Backed by rPM's world-renowned breakage warranty. For the Slash 2WD.

More information about HRP Distribution RPM80952 #ad


Similar products



Traxxas 1985 PTFE-coated washers, 5x8x0.5mm Set of 20

#ad
Traxxas TRA1985 #ad - For the Slash 2WD. Tech notes: rpm highly recommends the use of an RPM rear bumper mount #80902 or #80905 for full rear-end crash and bash-proof protection. Traxxas, truly the fastest name in Radio Control. 5x8x05mm 20 Ptfe-coated washers. Exploded views of your model can be found on the Traxxas website. Proudly made in the USA.

Tech notes: rpm slash 2wd rear a-arms only allow the use of the original, lower hole location to be used. No one has done more than traxxas to advance the RTR category with innovative thinking and fun designs that make it easy for anyone to get started in the great R/C hobby. Includes chassis, nerf bars 2, lower chassis, battery hold-down; front and rear battery retainers, and front shock springs.

Traxxas 1985 PTFE-coated washers, 5x8x0.5mm Set of 20 #ad - Complete kit, no additional parts required. Backed by rPM's world-renowned breakage warranty. Lowers chassis one inch 33mm/1. 3in. Traxxas has grown to become the number-1 selling name in RTR nitro and electric models for the last 4 years running. Designed to increase durability. Please refer to your vehicle's user for selecting the correct part.

More information about Traxxas TRA1985 #ad


Similar products



Hot Racing TE38CH Sealed Aluminum Differential Case for Traxxas 2wd Electric

#ad
Hot Racing HRATE38CH #ad - For the Slash 2WD. This item works with: traxxas bandit electric, slash 2wD all versions, Rustler XL-5, Stampede VXL, stampede electric, Rustler VXL Velineon Brushless, Stampede XL-5. Designed to increase durability. Rpm is proud american manufacturer designing and manufacturing 100% of our molded products right here in the USA!

Hot racing part number te38ch; UPC 083745813623. Lowers chassis one inch 33mm/1. 3in. Tech notes: weight comparison is based on the weight of the stock Traxxas bumper along with the weight of the support ring and hardware all of which is permanently removed once the RPM bumper skid plate is installed. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability.

Hot Racing TE38CH Sealed Aluminum Differential Case for Traxxas 2wd Electric #ad - 5x8x05mm 20 Use with ball bearings. Tech notes: rpm highly recommends the use of an RPM rear bumper mount #80902 or #80905 for full rear-end crash and bash-proof protection. Over 45% lower battery position. All hot racing upgrade parts are direct replacements for stock components; additional parts are not required.

These rear shock towers can be used on the Traxxas Bandit as well, However, there are no provisions for a rear wing built in.

More information about Hot Racing HRATE38CH #ad


Similar products



ST Racing Polished Steel Lock-nut Style Hinge-Pin for Traxxas 2WD Electrics

#ad
HRP Distribution SPTST3640BK #ad - To lower the rear end of the truck, RPM recommends using the outer shock mount hole positions in the A-arm. Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. Genuine Traxxas quality and precision. Tech notes: weight comparison is based on the weight of the stock Traxxas bumper along with the weight of the support ring and hardware all of which is permanently removed once the RPM bumper skid plate is installed.

Serious strength and rigidity while the chemical make up of our proprietary blend of nylons provides unmatched durability. For the Slash 2WD. Proudly made in the USA. 5x8x05mm 20 Please refer to your vehicle's user for selecting the correct part. This item works with: traxxas bandit electric, stampede electric, Rustler VXL Velineon Brushless, Stampede VXL, Slash 2WD all versions, Rustler XL-5, Stampede XL-5.

ST Racing Polished Steel Lock-nut Style Hinge-Pin for Traxxas 2WD Electrics #ad - Designed for traxxas electric stampede, Slash 2WD, Bandit, Rustler, and Monster Jam. High quality Polished Steel. Over 45% lower battery position. Backed by rPM's world-renowned breakage warranty.

More information about HRP Distribution SPTST3640BK #ad


Similar products