Smraza 10 Pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Car Boat Control, Arduino Project

#ad
Smraza #ad - Smraza 10 pcs 9g micro servo motor for rc robot Arm Helicopter Airplane Car Boat Remote Controls and Arduino Experiments Product Specification 1. Maximum angle: 120°. Mechanical specification: limit angle:200°± 1° weight:9 ± 1 g connector wire gauge:#28 PVC Connector wire length:250 ± 5 mm Spline:21T Horn type:Cross, star and bar-type Excessive play:≤0

5° 5. Fit for all kind of r/c toys and also make electronics DIY based on Arduino, Raspberry Pi. Interface type: compatible with jr & futaba interface. Stall torque 4. 8v: 17. 5oz /in 1kg/cm. Dead band setting: 7 microseconds. Comes with 1 year warranty and lifetime technical Support. Control specification: control system:change the pulse width amplifier type:analog controller operating trave:l120°±10° 900→2100 μsec left&right travelling angle deviation:≤ 6° Centering deviation:≤ 1° Neutral position:1500 μsec Dead band width:7 μsec Rotating direction:Counter Clockwise 900→2100μsec Pulse width range:900→2100 μsec Maximum travel:About 120° 900→2100 μsec Sg90 9g micro servo motor for remote control helicopters, micro robot, robot arm and boats.

Smraza 10 Pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Car Boat Control, Arduino Project #ad - Running speed at no load: 009 ± 001 sec/60°4. 8v 0

More information about Smraza #ad

ELEGOO 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

#ad
ELEGOO EL-SM-003 #ad - 5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board,with convenient use, connect to the 2 phase, direct docking - Rated Voltage: DC5V 4-phase - Insulation Resistance: >10MΩ 500V - Dielectric Strength: 600V AC / 1mA / 1s - Step angle: 5.625 x 1/64 - dc resistance: 200Ω±7% 25c - reduction ratio: 1/64 - insulation grade: a - no-load Pull in Frequency: >600Hz - No-load Pull out Frequency: >1000Hz - Pull in Torque: >34.

ELEGOO 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino #ad - 3mN. M120hz - detent Torque: >34. 3mN. M - temperature rise: 《40k120hz package including: 5 set uln2003 Stepper Motor + Driver Board 10pcs female to male cable as a gift Stepper motor with a standard interface, when used directly pluggable. A, b, c, d four-phase led indicates the status of the stepper motor work.

5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board,With convenient use, connect to the 2 phase, direct docking. Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in.

More information about ELEGOO EL-SM-003 #ad


Similar products



SunFounder PCA9685 16 Channel 12 Bit PWM Servo Driver for Arduino and Raspberry Pi

#ad
SunFounder miniLCD #ad - 5v compliant, which means you can control it from a 3. 3v microcontroller and still safely drive up to 6V outputs this is good when you want to control white or blue LEDs with 3. 4+ forward voltages. Support using only two pins to control 16 free-running PWM outputs - you can even chain up 62 breakouts to control up to 992 PWM outputs.

The only condition is that the main control chip supports I2C communication, which means enabling the communication between the chip and PCA9685, so as to control multiple servos simultaneously. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. 3 pin connectors in groups of 4, so you can plug in 16 servos at one time Servo plugs are slightly wider than 0

SunFounder PCA9685 16 Channel 12 Bit PWM Servo Driver for Arduino and Raspberry Pi #ad - 1" so you can only stack 4 next to each other on 01" header. For more information, please view at http://wiki. Sunfounder. Cc/index. Php?title=pca9685_16_channel_12_bit_pwm_servo_driver introduction pca9685 16-channel 12-Bit PWM Servo Driver can help a lot when there are insufficient PWM output pins for the MCU in your project.

It means, unlike the tlc5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running! Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board with a little gift.

More information about SunFounder miniLCD #ad


Similar products



Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry piPack of 3pcs

#ad
Onyehn #ad - It means, unlike the tlc5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running!12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. It's an i2c-controlled PWM driver with a built in clock. Green power-good LED.

Support using only two pins to control 16 free-running PWM outputs - you can even chain up 62 breakouts to control up to 992 PWM outputs. Terminal block for power input or you can use the 01" breakouts on the side. 3 pin connectors in groups of 4 so you can plug in 16 servos at once Servo plugs are slightly wider than 0

Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry piPack of 3pcs #ad - 1" so you can only stack 4 next to each other on 01" header. That means that, unlike the tlc5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! Output enable pin to quickly disable all the outputs. A spot to place a big capacitor on the V+ line.

5v compliant, which means you can control it from a 3. 3v microcontroller and still safely drive up to 6V outputs this is good when you want to control white or blue LEDs with 3. 4+ forward voltages.

More information about Onyehn #ad


Similar products



WMYCONGCONG 15 Nylon Control Horns 21x11 mm + Pushrod Connector Linkage Stopper 1.3mm + 1.2 x 180mm Steel Push Rods Parts for RC Airplane Plane

#ad
WGCD #ad - Communication Interface: IIC. It is 5v compliant, which means you can control it from a 3. 3v microcontroller and still safely drive up to 6V outputs this is good for when you want to control white or blue LEDs with 3. 4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs.

WMYCONGCONG 15 Nylon Control Horns 21x11 mm + Pushrod Connector Linkage Stopper 1.3mm + 1.2 x 180mm Steel Push Rods Parts for RC Airplane Plane #ad - Adjustable frequency pwm up to about 1. 6 khz;configurable push-pull or open-drain outputManufacturer. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. Lock on nylon control horns, Easy to install, designed with 4 holes, 21x11 mm, sturdy in flight. Push rod, easy to bend to fit the angles that you need, work great with the micro servos and projects.

Adjustable pushrod connector linkage stoppers, diameter of 1. 3mm, fit pushrods of 1. 0 / 1. 2 / 1. 1 / 1. 3mm. Application: vehicles & Remote Control Airplane Aircraft Toys. Package content: 5 x 1.

More information about WGCD #ad


Similar products



HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot

#ad
HiLetgo #ad - Contain an i2c-controlled pwm driver with a built-in clock. 16-way steering gear control. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board with a little gift. The pca9685 chip is wrapped in the center of the board.

Support using only two pins to control 16 free-running PWM outputs - you can even chain up 62 breakouts to control up to 992 PWM outputs. It means, unlike the tlc5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running!3 pin connectors in groups of 4, so you can plug in 16 servos at one time Servo plugs are slightly wider than 0

HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot #ad - 1" so you can only stack 4 next to each other on 01" header. Communication Interface: IIC. It is 5v compliant, which means you can control it from a 3. 3v microcontroller and still safely drive up to 6V outputs this is good for when you want to control white or blue LEDs with 3. 4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs.

Adjustable frequency pwm up to about 1.

More information about HiLetgo #ad


Similar products



Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

#ad
Elegoo EL-CP-004 #ad - Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board with a little gift. We have the manufacture factory, making productions and selling by ourselves. 16-way steering gear control. Support using only two pins to control 16 free-running PWM outputs - you can even chain up 62 breakouts to control up to 992 PWM outputs.

The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. Including 1x 40-pin male to female jumper wires, 1X 40-pin male to male jumper wires, 1x40-pin female to female jumper wires. We’d like to receive your valuable suggestions for our products and make your idea come true.

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino #ad - The pca9685 chip is wrapped in the center of the board. Component listing: 1pcs 40-pin male to female jumper wires 1pcs 40-pin male to malejumper wires 1pcs 40-pin female to female jumper wires Stepper motor with a standard interface, when used directly pluggable. A, b, c, d four-phase led indicates the status of the stepper motor work.

5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board,With convenient use, direct docking. Drive module board sizein: 1. 37*1. 18*0

More information about Elegoo EL-CP-004 #ad


Similar products



WGCD 10pcs Joystick Breakout Module Game Controller for Arduino PS2

#ad
WGCD 13 #ad - Size:37x25x32mm weight: 15 g connector: +5vcc - gnd - vrx - vry - sw material: abs plastic Game joystick module suits for Arduino PS2, the robot is at your commands with X, connects to two analog inputs, Y control. All pwm output lines have a 220 ohm series resistor protection and can easily drive LED.

Each cable length: about 20 cm /8-inch. Package: 10pcs joystick Breakout Module Stepper motor with a standard interface, when used directly pluggable. A, c, b, d four-phase led indicates the status of the stepper motor work.5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board,With convenient use, direct docking.

WGCD 10pcs Joystick Breakout Module Game Controller for Arduino PS2 #ad - Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. 100% brand new with high-quality, ABS plastic material, reusable. Do port for digital output, AO port for analog output. 16-way steering gear control.

More information about WGCD 13 #ad


Similar products



4PCS Servo Motor MG995 Control Angle180 Metal Gear Servo 20KG Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter

#ad
Deegoo #ad - Not designed for high current applications. This high-speed standard servo motor can rotate 180 degrees 90 in each direction. Compliant with most standard receiver connector: Futaba, Sanwa, Hitec, GWS etc. Stable and shock proof double coreless motor, ball bearing design, metal gear, Through external adapter, connector wire length 300mm.

4PCS Servo Motor MG995 Control Angle180 Metal Gear Servo 20KG Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter #ad - Stall torque: 12kg/cm6v, 13kg/cm7. 2v. Dimension: 407*19. 7*42. 9mm1. 6*078*1. 69inch. Gear type: all metal gears. Communication Interface: IIC. It is 5v compliant, which means you can control it from a 3. 3v microcontroller and still safely drive up to 6V outputs this is good for when you want to control white or blue LEDs with 3.

4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs. Adjustable frequency pwm up to about 1. 6 khz;configurable push-pull or open-drain outputManufacturer.

More information about Deegoo #ad


Similar products



Miuzei 10 pcs SG90 9G Servo Motor Kit for RC Robot Arm Helicopter Airplane Remote Control

#ad
Miuzei #ad - Stall torque 4. 8v: 17. 5oz /in 1kg/cm Dead band width: 7usec. Contain an i2c-controlled pwm driver with a built-in clock. Controllable angle range from 0 to 180 degrees, excellent linearity, precision control. All kind of r/c Toys and Arduino experiments. Packing in a color box. We have always cared about the customer experience and improve the product function details.

16-way steering gear control. 3 pin connectors in groups of 4, so you can plug in 16 servos at one time Servo plugs are slightly wider than 01" so you can only stack 4 next to each other on 01" header. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board with a little gift. Voltage: dc5-10V power supply.

Miuzei 10 pcs SG90 9G Servo Motor Kit for RC Robot Arm Helicopter Airplane Remote Control #ad - 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. Not designed for high current applications. This high-speed standard servo motor can rotate 180 degrees 90 in each direction. Compliant with most standard receiver connector: Futaba, Sanwa, Hitec, GWS etc. Stable and shock proof double coreless motor, Through external adapter, ball bearing design, metal gear, connector wire length 300mm.

More information about Miuzei #ad


Similar products



LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board for Arduino Nano x 3 with USB Cable

#ad
LAFVIN 8541582500 #ad - Specification:ch340G Replace FT232RL. Operating Voltagelogic level: 5V. 8 analog inputs ports:A0 ~ A7. 14 digital input / output ports:TX, RX, D2 ~ D13. 6 pwm ports:d3, d5, d10, d6, d9, D11.1 pairs of ttl level serial transceiver ports RX / TX. Support uSB download and Power. Support for external 5V ~ 12V DC power supply.

Support power supply by 9V battery. Support ISP download. Package including:3 x LAFVIN Nano V3. 0 with atmega328p module3 x usb cable Stepper motor with a standard interface, when used directly pluggable. A, c, b, d four-phase led indicates the status of the stepper motor work.5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board,With convenient use, connect to the 2 phase, direct docking.

LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board for Arduino Nano x 3 with USB Cable #ad - Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. No load running Speed: 0

More information about LAFVIN 8541582500 #ad


Similar products