Soulload 3DR 100MW Radio Telemetry Kit 915Mhz 915 Kit Air and Groud Data Transmit Module for APM2.6 APM2.8 PX4 Pixhawk

#ad
Soulload #ad - Firmware upgrades and configuration are fully supported in the APM Mission Planner. The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface, based on HopeRF's HM-TRP data link modules, and custom firmware that improves upon the modules' original features and performance.

The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface, based on HopeRF's HM-TRP data link modules, and custom firmware that improves upon the modules' original features and performance. The sik firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters.

Support otg of android cellphones, and computer OTG. Pre-configered and tested to 115200 BAUD rate, and all other settings needed. The 3dr radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. 3dr telemetry 915mhz set for multiwii setting.

Soulload 3DR 100MW Radio Telemetry Kit 915Mhz 915 Kit Air and Groud Data Transmit Module for APM2.6 APM2.8 PX4 Pixhawk #ad - Antenna is 5. 8g, not the cheap 2. 4g whose range is very small and material is very cheap like others. 3dr telemetry kit specifications - very small size - light weight under 4 grams without antenna - receiver sensitivity to -118 dbm - transmit power up to 20dbm 100mw - transparent serial link - air data rates up to 250kbps - mavlink protocol framing and status reporting - Frequency hopping spread spectrum FHSS - Adaptive time division multiplexing TDM - Support for LBT and AFA - Configurable duty cycle - Built in error correcting code can correct up to 25% data bit errors - Demonstrated range of several kilometers with a small omni antenna - Can be used with a bi-directional amplifier for even more range - Open source firmware - AT commands for radio configuration - RT commands for remote radio configuration - Adaptive flow control when used with APM -Based on Si1000 microcontrollers Package included: 1 set of 3DR 100mW 915mHz Radio Telemetry kit  Upgrated 3dr 100mw 915mhz radio telemetry.

More information about Soulload #ad

Readytosky Pixhawk PX4 Flight Controller Autopilot PIX 2.4.8 32 Bit Flight Control Board+Safety Switch+Buzzer+I2C Splitter Expand Module+16GB SD Card

#ad
Readytosky X81 #ad - 2 can 3. Spektrum dsm / dsm2 / dsm-X satellite receiver compatible input 4. Futaba sbus compatible inputs and outputs 5. Ppm signal Input 6. Rssi pwm or voltage Input 7. I2c 8. Spi 9. 3. 3 and 6. 6vadc input 10 The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system; 2.

Frequency: 168mhz, 256K RAM 3. 32 stm32f103 backup coprocessor Sensor 1. L3gd20 3-axis digital gyroscope 16 2. Lsm303d 3-axis accelerometer 14 / Magnetometer 3. Mpu6000 6-axis accelerometer / magnetometer 4. Ms5607 precision barometer Interface 1. 5 high voltage compatible UART 1, 2 with hardware flow control 2. We have m8n gps for this flight controller, ASIN : B01KK9A8QG.

Readytosky Pixhawk PX4 Flight Controller Autopilot PIX 2.4.8 32 Bit Flight Control Board+Safety Switch+Buzzer+I2C Splitter Expand Module+16GB SD Card #ad - . External micro usb interface Packing list: 1 x Pixhawk 2. 4. 8 32bit arm flight controller 1 x original shell 1 x pixhawk safety switch 1 x pixhawk buzzer 1 x 8g tf cardio firmware has written 1 x Servo cable 1 x 4pin turn 4pin cable 1 x 3pin DuPont line 1 x Pixhawk I2C Splitter Expand Module The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;.

Provide automatic and manual modes; 6.

More information about Readytosky X81 #ad


Similar products



powerday APM Power Module V1.0 XT60 Female Male Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
Rcmodel 49122 #ad - Voltage and current measurement configured for 5V ADC. Used to detect the battery voltage and the battery current, flight control board receives two signals, calculate the remaining battery power, estimate the remaining flight time. Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control.

32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit. Another signal cable connectors are used in Japan original fittings, non-domestic joint, so APM flight control board and reliable connection between the power supply module. 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector.

powerday APM Power Module V1.0 XT60 Female Male Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller #ad - Use your aircraft's own ESC/BEC for that. Package include: -1x APM Power Module V1. 0 the advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;. In addition the module also comes with BEC function, you can output 5. 3 dc, 3a maximum continuous current for the flight control board to provide a stable power supply.

The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 4S LiPo battery.

More information about Rcmodel 49122 #ad


Similar products



Cylewet 6Pcs APM 2.6 2.52 Flight Control Cable Mixed Specification 4P 5P 6P Position Connector Pack of 6 CYT1011

#ad
Qianxin LYSB01N4IRVQI-ELECTRNCS #ad - The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Use your aircraft's own ESC/BEC for that. Length: 20cm/ 7. 87inches. It is not designed to power servos.

Designed to be used on the Pixhawk, APM and PX4 board series. Switching regulator outputs 5. 3v and 3A max. We have m8n gps for this flight controller, ASIN : B01KK9A8QG. Max input voltage: 30V, Max current sensing: 90A. Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control.

Cylewet 6Pcs APM 2.6 2.52 Flight Control Cable Mixed Specification 4P 5P 6P Position Connector Pack of 6 CYT1011 #ad - 32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit. Specification: 4p 5P 6P; 20cm/ 7. 87inches package includes: 2× 4p 2× 5p 2× 6p the advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;. 6-pos df13 cable plugs directly to APM 2.

5's 'pm' connector.

More information about Qianxin LYSB01N4IRVQI-ELECTRNCS #ad


Similar products



Readytosky M8N GPS Module Built-in Compass Protective Case with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 Flight Controller

#ad
Readytosky XGT60-BLACK #ad - 40° c to 85° c - -40° c to 105° c - rohs compliant lead-free package includes 1xm8n gps module Built-in Compass - 1x Black GPS Holder ★Important:The GPS light only can light up when it search the satellite signal outdoor. Use your aircraft's own ESC/BEC for that. Length: 20cm/ 7. 87inches. The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;.

Readytosky M8N GPS Module Built-in Compass Protective Case with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 Flight Controller #ad - This communication cable uses the Hirose DF13 series connector. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. Special designed for pixhawk 2. 4. 6 2. 4. 8 flight controller, aSIN:B07CHQ7SZ4. Note:if you use it to aPM Flight Controller, Please replace the connect by yourself.

The ultimate accuracy is 06 meters, actually almost 09 meters, greater than the previous generation NEO-7N 1. 4-1.

More information about Readytosky XGT60-BLACK #ad


Similar products



FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver

#ad
FrSky NPH-01266 #ad - Designed to be used on the Pixhawk, APM and PX4 board series. For 8 channels in d8 mode you can use the FrSky Taranis or XJT, DFT, DHT and DHT-U modules. Switching regulator outputs 5. 3v and 3A max. Parallel two x8R to become a 16 channel receiver. Smartport enabled, realizing two-way full duplex transmission.

FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver #ad - More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver. All 16 channels requires the frsky taranis, djt, or the xjt module bound in d16 mode. Features: more number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver.

Specifications: number of Channels: 16 Dimension: 46. 5mm x 27mm x 14. 4mm 1. 83" x 1. 06" x. 56" weight: 16. 8g. 59 oz operating VoltageRange: 4V-100v operating current: [email protected] Operating Range: >1.

More information about FrSky NPH-01266 #ad


Similar products



FrSky X4RSB 3/16CH Telemetry Receiver with Futaba SBUS 16 Channels Smart Port

#ad
FrSky NPH-01213 #ad - Parallel two x8R to become a 16 channel receiver. Smartport enabled, realizing two-way full duplex transmission. More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port, or combine two X8R to become a 16 channels receiver. All 16 channels requires the frsky taranis, djt, or the xjt module bound in d16 mode.

Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control. 32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit. Switching regulator outputs 5. 3v and 3A max. Special designed for pixhawk 2. 4. 6 2. 4. 8 flight controller, aSIN:B07CHQ7SZ4. Note:if you use it to aPM Flight Controller, Please replace the connect by yourself.

FrSky X4RSB 3/16CH Telemetry Receiver with Futaba SBUS 16 Channels Smart Port #ad - The ultimate accuracy is 06 meters, actually almost 09 meters, greater than the previous generation NEO-7N 1. 4-1.

More information about FrSky NPH-01213 #ad


Similar products



3DR Pixhawk Mini Autopilot

#ad
3D Robotics, Inc. 3DR Pixhawk Mini #ad - It is not designed to power servos. External analog telemetry port AD2. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Voltage and current measurement configured for 5V ADC. We have m8n gps for this flight controller, ASIN : B01KK9A8QG. Max input voltage: 30V, Max current sensing: 90A.

This communication cable uses the Hirose DF13 series connector. Abundant connectivity options for additional peripherals UART, I2C, CAN. Improvements over the original pixhawk: smaller, included gps module ublox m8n gps/glonass/beidou receiver for faster and stronger gps lock, integrated piezo speaker and safety switch, a third of the size, micro JST rather than the hard-to-use DF13 connectors, Rev 3 processor for long term software support, both primary and secondary IMU MPU9250 and ICM20608 for more reliable flight, improved sensors, natively supports 4S batteries with the included PDB.

3DR Pixhawk Mini Autopilot #ad - For 8 channels in d8 mode you can use the FrSky Taranis or XJT, DFT, DHT and DHT-U modules. Rssi pwm output. Two selectable failsafe setting options - native failsafe or user programmable failsafe. Integrated multi-tone piezo audio indicator. Microsd card for long-time high-rate logging The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;.

Use your aircraft's own ESC/BEC for that.

More information about 3D Robotics, Inc. 3DR Pixhawk Mini #ad


Similar products



HATCHBOX PLA 3D Printer Filament, Dimensional Accuracy +/- 0.03 mm, 1 kg Spool, 1.75 mm, Red

#ad
HATCHBOX 3D PLA-1KG1.75-RED #ad - The advanced 32-bit arm cortexm4 high-performance processors, can run NuttX RTOS real-time operating system;. Recommended extrusion/nozzle temperature 180°C - 210°C 356°F - 410°F. It is not designed to power servos. The filaments are universally designed and compatible with 3D Printers using 1. 75mm diameter filament, with a dimensional accuracy of +/- 0

03mm. Rev 3 processor for long-term software support. Improved sensors, both primary and secondary IMU MPU9250 and ICM20608 for more reliable flight. Included gps module ublox m8n gps/glonASS/BeiDou receiver for faster and stronger GPS lock. Micro jst rather than the hard-to-use DF13 connectors. 1 kg approximately 2.

HATCHBOX PLA 3D Printer Filament, Dimensional Accuracy +/- 0.03 mm, 1 kg Spool, 1.75 mm, Red #ad - 20 lbs. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. Two selectable failsafe setting options - native failsafe or user programmable failsafe. Pla polylactic acid 3d Printer Filament Vacuumed Sealed With Desiccant. Designed to be used on the Pixhawk, APM and PX4 board series.

Because of the lower melting temperatures and lack of warping, PLA filaments retain their color vibrancy and are a common choice for displays or small household prints.

More information about HATCHBOX 3D PLA-1KG1.75-RED #ad


Similar products



Pixnor Apm2.6 MWC GPS Compass Antenna Folding Fixed Mount Bracket Holder for DJI Red

#ad
Pixnor 172354O63OI5005 #ad - Pla polylactic acid 3d Printer Filament Vacuumed Sealed With Desiccant. For 8 channels in d8 mode you can use the FrSky Taranis or XJT, DFT, DHT and DHT-U modules. Rssi pwm output. Spool. Provide redundant power input and failover. 5 high voltage compatible UART 1, 2 with hardware flow control. 32 2 mb flash stm32f427 cortex M4, with hardware floating-point processing unit.

Pixnor Apm2.6 MWC GPS Compass Antenna Folding Fixed Mount Bracket Holder for DJI Red #ad - 100% brand new and high quality cNC Aluminum GPS Folding Antenna Base Mount Holder Bracket Set. 1. 75mm filament diameter Dimensional Accuracy +/- 003mm. Material: durable aluminum. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Adopt aluminum turning and CNC manufacturing for durable to use.

Easy to itall and use. 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector. Features - Color: mainly red. With easy to itall and use, it is really a wonderful GPS folding antenna holder for choice.

More information about Pixnor 172354O63OI5005 #ad


Similar products



Hobbypower Power Module V1.0 with XT60 Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
Hobbypower #ad - Pla polylactic acid 3d Printer Filament Vacuumed Sealed With Desiccant. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe. Color: mainly red. Another signal cable connectors are used in Japan original fittings, non-domestic joint, so APM flight control board and reliable connection between the power supply module.

Use your aircraft's own ESC/BEC for that. Specifications: max input voltage: 30v max current sensing: 90A Size:25*21*9mm Net weight:25g Voltage and current measurement configured for 5V ADC Switching regulator outputs 5. 3v and 3a max 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector note: the power module is only designed to power APM, a RC receiver and APM accessories GPS, 3DR radio.

Hobbypower Power Module V1.0 with XT60 Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller #ad - The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection. Used to detect the battery voltage and the battery current, calculate the remaining battery power, flight control board receives two signals, estimate the remaining flight time. In addition the module also comes with bec function, you can output 5.

3 dc, 3a maximum continuous current for the flight control board to provide a stable power supply. Spool. Parallel two x8R to become a 16 channel receiver.

More information about Hobbypower #ad


Similar products